- What happens if lightning strikes a metal roof?
- Do Metal Roofs need a drip edge?
- Should metal roofs be grounded?
- Does a metal roof make your house hotter?
- What is the underside of a roof overhang called?
- How much overhang should a plywood roof have?
- Can you install drip edge after gutters?
- Can I put metal roofing over OSB?
- How far should roof overhang gutters?
- How far can roof overhang without support?
- Should plywood go under metal roof?
- Can you put metal roofing directly over shingles?
- How much should a corrugated roof overhang?
- Do you need felt paper under metal roofing?
- Do houses with metal roofs need gutters?
- Is metal drip edge required by code?
- What are the disadvantages of a metal roof?
- How far can you cantilever a 2×8 roof?
What happens if lightning strikes a metal roof?
A metal building system, with a conductive metal roof and a conductive metal structural frame, gives lightning a low-resistance path to the earth.
The short answer is, no, a metal roof will not make lightning more likely to strike, but it may make a lightning strike less dangerous if it occurs..
Do Metal Roofs need a drip edge?
A: A drip edge is not always required by local building codes, but installing a drip edge is a good idea—especially if the home is in an area that experiences a lot of wind-driven rain. This applies whether you are working with asphalt or metal because a drip edge allows water to fall away from the fascia.
Should metal roofs be grounded?
The short answer is no, a metal roof does not need to be grounded. In most cases, you will not incur additional risk if you don’t ground it. Metal does conduct electricity. But when dealing with a full roof, a lightning strike would ground out through the structure, causing no more harm than non-metal roofs would.
Does a metal roof make your house hotter?
Since metal roofs have a low thermal mass, they reflect light and heat rather than absorbing it like asphalt shingles. This means that rather than making your home hotter during the summer months, metal roofing actually helps keep it cool, increasing the energy efficiency of your home.
What is the underside of a roof overhang called?
Roof edge (or eaves edge) Also known as a fascia.
How much overhang should a plywood roof have?
The overhang is multiple meaning that the sheeting you would overhang some 3/4-1″ followed by a drip edge then if using shingles another 1″. If using metal w/o drip another 3/4-1″ past the wood sheeting. You would want to keep your completed overhang close to 1-1/2″ if using gutter.
Can you install drip edge after gutters?
If the overlap is too short, fix it by placing drip edge under the first row of roof shingles and be sure that the exterior edge is reaching over the gutter. If the gutter is lower than the bottom edge of the drip edge, install flashing behind the drip edge and over the back edge of the gutter to remove the gap.
Can I put metal roofing over OSB?
No, you do not need to screw into solid lumber (joists, stripping,etc.). As you can see, the thinnest material they recommend is 1/2” (7/16”) OSB board at 9” on center up to 24” on center. Be sure to follow their instructions in order to obtain the warranty. Metal roofing screws need to go into framing.
How far should roof overhang gutters?
50mmWe recommend 50mm overhang into a standard gutter.
How far can roof overhang without support?
Two feet is the general maximum length for a typical roof overhang. This will protect a roof from most types of damage. Roof overhangs can extend farther than 2 feet, but beyond this length, they begin to lose structural integrity and require external support.
Should plywood go under metal roof?
As long as the interior of your roof is protected from moisture accumulation, underlayment is not required, though homeowners planning to insulate their house heavily may choose to install plywood to protect their investment. …
Can you put metal roofing directly over shingles?
In almost every case, the answer is yes, you can lay down a new metal roof over an existing shingle roof. This is one of the many reasons metal roofs keep growing in popularity – their installation doesn’t require completely tearing off the existing roof, which is a time-consuming and expensive job.
How much should a corrugated roof overhang?
Little Metal Roof Overhang A typical metal roof overhang may be 2 to 4 inches, or even less. Some slight overhang is recommended, in conjunction with a drip edge flashing, to prevent water from getting under the roofing and onto underlying wood.
Do you need felt paper under metal roofing?
The simple answer is yes, your roof does need an underlayment. … If your metal roof is going on top of asphalt shingles, then there is already an underlayment, and it likely doesn’t need another. Keep in mind, however, that expansion and contraction of the shingles could cause damage to the back of the metal over time.
Do houses with metal roofs need gutters?
Strictly speaking, metal roofs do not require gutters because metal roofs themselves are resistant to the damage gutters are designed to prevent. However, gutters do play a significant role in protecting other parts of your property.
Is metal drip edge required by code?
The International Residential Code (IRC) did not require metal drip edges along eaves and rake edges until the 2012 edition (See Code Requirements for Drip Edge, above). So depending on where you work and what code prevails in that area of the country, metal drip edges still may not be required by code.
What are the disadvantages of a metal roof?
Disadvantages of metal roofsAffordability. Metal roofs can be as much as two or three times more expensive than other roofing materials. … Noisiness. Metal roofs can be noisy, especially during a heavy rain or hailstorm. … Expansion and contraction. … Inconsistency of color match. … Performance.
How far can you cantilever a 2×8 roof?
Deck Joist Cantilever Rules and LimitsJoist Spacing (o.c.)24″Douglas Fir-Larch, Hem-Fir, Spruce-Pine-Fir2x61′-2″2×82′-2″2×102′-9″2×123′-3″9 more rows•May 30, 2017